Homebrewing - Home Brewers Blog

West Coast Brewer Home Brewing Blog

Tag: brew sculpture

Brewed up a Batch of Coffee Milk Stout over the weekend!

Home beer brewery setup

Home beer brewery setup

 

This weekend I brewed up a batch of Coffee Milk Stout.  If it turns out well, I will be sure to post the recipe for it.  It should ride that line in between stout and imperial stout.  I also chose to diminish the hop profile on it a bit so that the coffee flavors could be showcased on this batch.  I am also going to try adding a cold brewed coffee concentrate to the fermenter after about a week instead of adding coffee beans to the fermenter.  Fingers crossed that this will turn out well!

Brew Stands and Home Brewing Racks

Brew Stands and Homebrewing Racks

Brew Stands and Homebrewing Racks

I recently added a new page to the West Coast Brewer main site for brew stands, homebrewing racks, home breweries, beer brewing stands and home brew racks!  Whatever name you want to call them by, they can be found here:

Home Brewing Stands

 

My goal is to list all of the turnkey \ pre-built homebrew racks that I can find available for sale online there, so if you know of any that I have not listed, please feel free to shoot me an email about it so that I can get them added.

 

The page features the whole range of home brewing stands from entry level to digital stainless steel brew racks and photos of each stand.  There are several single tier models as well as multi tier homebrew stands to chose from.  The prices range from about $500 for a bare homebrew stand to over $6000 for a complete home brewing rack with kettles, pumps and digital temperature controllers.

 

Boosting your home beer brewing burners efficiency!

How to improve your burner efficiency

How to increase your propane burner efficiency

 

About a year ago I upgraded from my previous low output propane burners to these larger 210,000 BTU Banjo Burners.  These new burners were literally about 4 times larger, heavier and produced about 4 times the BTU’s as my previous propane home brewing burners and I had high expectations of them.  When it finally came time to test them out on a batch of beer I was left somewhat disappointed.  Did they heat my kettles more quickly?  Yes they did.  Were they terribly inefficient and double by propane expenses?  Yes, they did that too.

 

I was please with how much time they were saving, but was very let down by how much propane I was blowing through.  In the past I was able to get about 4, 10 gallon batches from each propane tank.  With these new banjo burners I was getting less than 2.  Based on what I could tell from observation, much of the heat was being reflected off of the bottom of the kettles and pushed out of the sides burner housing.  My plan was to create 2 metal baffles to help better direct the heat where I wanted it to go.  I bolted the first baffle around the internal burner housing about 1 1/2 inches bellow where the kettle sits.  I welded the second baffle near the outside of the burner housing, just slightly larger then the approximate diameter of my kettles.  The top of the second baffle was approximately 1/2 inch beneath the kettle.  I left a small area of space for me to pass through my igniter.

 

Improving Banjo Burner Efficiency

Improving Banjo Burner Fuel Efficiency

 

After testing these baffles I was very pleased with the efficiency gains to my home brewing banjo burners.  I was back to getting about 3 1/2, 10 gallon batches per propane tank and was heating my kettles about twice as fast as I was with my previous burners.  If anyone else has been experiencing similar issues with their propane burner efficiency, hopefully this will help you out.

 

All Grain Home Brewing

All Grain Home Brewing

All Grain Home Brewing and Beer Making

 

I figured that I would give a simple break down on all grain home brewing for those of you who have been doing extract brewing for a while and are considering making the change but want some basic information on what you are in for before you do.

 

So what is the difference between extract brewing and all grain brewing?   With extract brewing, the home brewer bypasses the mashing process and instead uses either concentrated dried malt extract (DME) or liquid malt extract (LME) to brew his or her beer. This greatly lowers the complexity of the home brewing process since the brewer does not need to worry about water pH levels, mash conversion temperatures, water profile composition, sparging, lautering or things like tannin extraction problems.  Also, the extract home brewing takes far less time and equipment than all grain home brewing.  With all grain brewing, you do not utilize any forms of malt extracts and instead convert all of the sugars yourself from grain starches and adjuncts.  With all grain home brewing it is important to check your gravity readings throughout the brewing process to make sure that you are not extracting too much or two little sugar.  You are also in charge of the type of sugars that are created during the mashing process.  If your mash temperature is a few degrees to high your beer may come out very sweet, if it is a few degrees to low you may end up with a very dry beer.  Mastering all grain brewing is all about understanding the process, tailoring the process to the style of beer you are brewing and being as exact as possible.

 

So what equipment will you need to do all grain home brewing that you do not need for extract brewing?  Unless you are going to go the brew in a bag route, you are probably going to want 3 kettles and or combinations of 3 kettles \ coolers.  One will be your Hot Liquor Tank (HLT) which will allow you to quickly modify the temperature of your mash during the different steps of the starch conversion process.  The second is your Mash Tun which is where you will place your grains and convert the starches to sugars.  A mash tun typically uses a false bottom which allows the wort to pass through it during the lautering and mash out process but restricts the grain husks from being transferred to the boil kettle.  If you will be conducting a fly sparging process, which many home brewers do in order to boost your efficiency of extracting the sugars from your grains, you will also need to purchase a sparge arm.  Lastly you will need a boil kettle that has a sufficient volume for the quantity of wort that you will be boiling.  Aside from that, the equipment is very similar to what you would use during the extract home brewing process.

 

If you are looking for a ready-made all grain home brewing stand, brewing sculpture or home brewery; there are several options available here that range from cooler based setups to stainless steel home brewing racks!

Home Brewing Stands, Brewing Racks, Brew Sculptures and All Grain Starter Kits

Pre-Built Beer Racks, Home Breweries, Brewing Stands and Brew Sculptures

 

Brewing Sculpture

Turnkey Home Brewery – Morebeer.com – Single Tier Home Brewing Rack

 

 

If you are interested in purchasing one of these all grain home brewing stands, you can view their full lineup here:

Click Here For Stainless Steel Home Brewing Stands

 

Pre-built beer stands, turnkey home breweries, pre-made brew sculptures, single tier brewing stands, multi tier home breweries… call them what you will.  Before your only option was to build your own brewing stand, but now, if you have the money; there are several pre-built home brewery options available.  So which is the best option for your money?

 

If I had not already gone through the blood, sweat, tears and frankly burns of welding and constructing my own single level home brewing stand; I would opt for one of MoreBeers brewing sculptures.  Over the last 5 years they seem to have perfected the pre-manufactured beer rack.  They have 3 styles of brewing sculptures available for you to choose from; a stainless steel single tier brewing rack, a 3 tier tippy-dump brewing sculpture and a 3 level gravity based home brewery.  I would personally go with their single tier home brewing stand, but if you have space limitations or can not afford the hefty price tag of the single level brewing stand, the stainless steel multi tier brewing stands are a great option as well.

 

 

3 Tier Home Brewing Rack

Multi-level home brewing stand – MoreBeer Tippy-Dump Stainless Steel Brewing Stand

 

What I like most about MoreBeer’s stainless steel brewing stands, over the other pre-constructed brewing stands on the market is that they seem to have thought of everything in their design and did not skimp on any of the features.  Their brewing racks are all made out of stainless steel and many of their versions include the following features:

  • Stainless Steel Maximizers and Diverter
  • High Temperature March Pumps
  • The MoreBeer Stainless Steel Ultimate Sparge Arm
  • Digital Temperature Controls
  • Control Panel
  • Convoluted Heat Exchanger for RIMS and HERMS support
  • Boil Kettle Whirlpool Arm
  • Fantastic Customer Support
  • Hard propane lines

The only downside that I can see is the price.  One of these stainless steel home brewing stands will run you anywhere from $1099  to over $6000 depending on the style, capacity and features that you want in your brewing sculpture.  In all reality that is not too bad of a deal when you consider that it comes with the kettles and almost all of the items that you will need to have an out of the box, ready to go, top of the line all grain home brewery constructed from stainless steel.

 

If you are interested in purchasing one of these all grain home brewing stands, you can view their full lineup here:

Click Here For Stainless Steel Home Brewing Stands

 

 

 

%d bloggers like this: