West Coast Brewer Home Brewing Blog

How to install a thermowell

How to install a thermowell in a stainless steel brew kettle or fermentor.

How to Install a Thermowell

How to Install a Thermowell

 

I live in Southern California and it is not unusual for me to get daily temperature deviations of more than 30 degrees depending on the time of the day.  As you can imagine, this makes regulating fermentation temperatures a bit of a nightmare.  So about a year and a half ago I purchased a chest freezer to use as a fermentation chamber.  The chest freezer greatly helped in creating a more stable environment for my fermentation but I was taping the temperature probe of my digital thermostat to the side of my carboy or fermentor and that was not giving me a true reading of the actual temperature of the fermenting beer. As beer ferments, especially during times of high yeast activity a good amount of heat is created inside the fermentation vessel which means that the temperature of the beer can differ significantly from the ambient temperature of your fermentation chamber.  If the temperature in your fermentation vessel gets to high, your yeast may begin to create off or undesired flavors in your beer.  Since the heat produced by yeast activity changes significantly over the course of fermentation, simply compensating by moving the thermostat temperature down a few degrees is not ideal.  For this reason, many home brewers choose to either purchase a fermentor with a thermowell built in or add a thermowell to their fermentor.

 

A thermowell is a hollow thin walled tube that reaches from the outside wall of the fermentor to a near center point of the inside of the fermentor.  The hollow chamber of the thermowell allows you to insert a thermostat temperature probe so that you can get a far more precise reading of the actual temperature inside of the fermentation vessel.

 

For my fermentation vessel I use a 7 Gallon Stainless Steel Brew Bucket.  If is far less expensive than some of the higher end stainless steel fermentors but unfortunately it does not come with a thermowell built in.  That being said, it still costs a couple hundred dollars and the last thing that I wanted to do was ruin it by improperly installing a termowell. After doing a little research I was able to install the thermowell with no issues and it only took me about 20 minutes to do.  The tools that I used were a center punch, hammer, electric drill, 2 small drill bits, step drill bit, crescent wrench and a little fine grit sand paper.

 

How to Install A Thermowell Step1

How to Install A Thermowell Step1

 

First things first, you will want to gather your tools and mark the point on your fermentor where you want to place your thermowell.  The thermowell should be near the center of the fluid level of your filled fermentor.  Also consider that if you prepare different sized batches in your fermentor, you will want to place the thermowell so that it will be able to read the temperature of small batch sizes as well, so it may make sense to place the thermowell a little lower in the fermentation vessel.  After you mark your installation spot on your fermentor, you will want to use a punch or sharp instrument to make a starting point for when you drill your pilot hole.

 

Thermowell Installation Step 2

Thermowell Installation Step 2

 

 

Next you will want to drill your pilot hole as shown in the image above.  In my situation I actually increased the size of the initial pilot hole with a slightly larger drill bit to help accommodate the head of my step drill bit.

 

 

Thermowell Install Step 3

Thermowell Install Step 3

 

I then used my step drill bit to increase the diameter of the hole until the thread of my thermowell was  able to enter it snugly.  Once I verified that it was able to enter, I used the fine grit sand paper to remove any sharp metal and to polish the edges of the drilled hole.  Next I mounted the thermowell, making sure to use the included silicone o-ring.

 

Thermowell Step 4

How to Install a Thermowell Step 4

 

 

Lastly I cleaned the fementor and thermowell and tested it to insure that there were no leaks.  The install was a success and I currently have a batch of beer in it and the thermowell is working well as expected!

 

If you are looking to either purchase a fermentor or a thermowell for an existing fermentor, here is where I purchased mine.

 

Click Here for Fermentors and Thermowells

 

1 Comment

  1. Valmik Patel

    Great Post. Thanks for sharing this. Really helpful.

Leave a Reply About This Home Brewing Article